| Last Modified: 11-29-2007 | 1.6 J | |
| Service Category: Vehicle Exterior | Section: Mirror (ext) | |
| Model Year: 2008 | Model: Sequoia | Doc ID: RM000002NOP008X |
| Title: MIRROR (EXT): POWER MIRROR CONTROL SYSTEM (w/ Memory): SYSTEM DESCRIPTION (2008 Sequoia) | ||
|
Reverse Shift-linked Function of Power Mirrors does not Operate |
SYSTEM DESCRIPTION
When the reverse signal is sent from the ECM through the CAN communication line to the outer mirror control ECU, the outer mirror control ECU activates the outer rear view mirror LH and RH reverse shift-linked function.
HINT:
The reverse shift-linked function will not occur when the outer mirror reverse gear link switch is not ON.
WIRING DIAGRAM
INSPECTION PROCEDURE
PROCEDURE
|
1. |
CHECK DTC |
(a) Use the Techstream to check if the CAN communication system is functioning normally
.
Result
|
Result |
Proceed to |
|---|---|
|
CAN DTC is not output |
A |
|
CAN DTC is output |
B |
|
|
2. |
READ VALUE USING TECHSTREAM (PARK/NEUTRAL POSITION SWITCH) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream ON.
(d) Enter the following menus: Powertrain / ECT / Data List.
(e) According to the display on the Techstream, read the Data List.
ECT
|
Tester Display |
Measurement Item/Display |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
Shift SW Status (R Range) |
PNP switch status / ON or OFF |
ON: Shift lever in R OFF: Shift lever not in R |
- |
OK:
On the Techstream screen, each item changes between ON and OFF according to above chart.
Result
|
Result |
Proceed to |
|---|---|
|
OK |
A |
|
NG (A750E automatic transmission) |
B |
|
NG (A750F automatic transmission) |
C |
|
NG (AB60E automatic transmission) |
D |
|
NG (AB60F automatic transmission) |
E |
|
|
3. |
READ VALUE USING TECHSTREAM (MIRROR POSITION SENSOR) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream ON.
(d) Enter the following menus: Body Electrical / Mirror / Data List.
(e) According to the display on the Techstream, read the Data List.
Mirror
|
Tester Display |
Measurement Item/Display |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
RH Mir Position Sensor V |
RH side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V |
Within range from 0 to 5 V |
- |
|
LH Mir Position Sensor V |
LH side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V |
Within range from 0 to 5 V |
- |
OK:
When mirror control switch is operated to turn mirror upward or downward, voltage changes within range shown in above chart.
Result
|
Result |
Proceed to |
|---|---|
|
Neither mirror operates normally |
A |
|
LH side mirror does not operate normally |
B |
|
RH side mirror does not operate normally |
C |
|
Mirror operates normally |
D |
|
|
4. |
INSPECT OUTER MIRROR REVERSE GEAR LINK SWITCH |
|
(a) Remove the switch. |
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
3 - 6 |
Pressed |
Below 1 Ω |
|
Not pressed |
10 kΩ or higher |
|
|
5. |
CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH - OUTER MIRROR CONTROL ECU) |
|
(a) Disconnect the M8 ECU connector. |
(b) Disconnect the H76 switch connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
H76-3 (E)- Body ground |
Always |
Below 1 Ω |
|
M8-36 (AR) - H76-6 (B) |
Always |
Below 1 Ω |
|
M8-36 (AR) - Body ground |
Always |
10 kΩ or higher |
|
|
6. |
CHECK OUTER MIRROR CONTROL ECU |
|
(a) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
M8-3 (E1) - Body ground |
Always |
Below 1 Ω |
|
|
7. |
CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER MIRROR CONTROL ECU) |
|
(a) Disconnect the M8 ECU connector. |
(b) Disconnect the M5 mirror connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
M5-15 (VC) - M8-2 (VC) |
Always |
Below 1 Ω |
|
M5-15 (VC) - Body ground |
Always |
10 kΩ or higher |
|
M5-17 (VSRL) - M8-4 (VSR) |
Always |
Below 1 Ω |
|
M5-17 (VSRL) - Body ground |
Always |
10 kΩ or higher |
|
M5-18 (E1) - M8-3 (E1) |
Always |
Below 1 Ω |
|
M5-18 (E1) - Body ground |
Always |
10 kΩ or higher |
|
|
8. |
CHECK OUTER MIRROR CONTROL ECU |
|
(a) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
M8-23 (E1) - Body ground |
Always |
Below 1 Ω |
|
|
9. |
CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR CONTROL ECU) |
|
(a) Disconnect the M8 ECU connector. |
(b) Disconnect the L6 mirror connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
L6-15 (VC) - M8-22 (VC) |
Always |
Below 1 Ω |
|
L6-15 (VC) - Body ground |
Always |
10 kΩ or higher |
|
L6-17 (VSSR) - M8-24 (VSSR) |
Always |
Below 1 Ω |
|
L6-17 (VSSR) - Body ground |
Always |
10 kΩ or higher |
|
L6-18 (E1) - M8-23 (E1) |
Always |
Below 1 Ω |
|
L6-18 (E1) - Body ground |
Always |
10 kΩ or higher |
|
|
|